STK Professional Audio

HOME > PRODUCTS > ACTIVE SPEAKERS

SP-1812AP	SP-158AP	SP-K615AP	SP-K618AP	SP-1563AP	SP-156AP
SP-155AP	SP-115APM	SP-112APM	SPM-155AP	SPM-152AP	SPM-122AP

SP-156AP

Front View / Rear View

Manual / Dimensions

Real one for two systems with powerfull out put !!
The SP156AP is dual power full-range 300WX2 amplified enclosure with one 15” SK15300H low frequency drivers vented.
Designed for portable systems,the active stereo mode required from AV music and active parallel mode for distributed installation design.
The one power outputs dedicated to powering internal 15" LF driver with HF compression driver and the other one full range power outputs used to drive the Passive SP152H speaker or equivalent systems.

2-Way full-range dual Amp active system.
High output and with very low THD and broadest bandwidth.
The one 2” SK60D exit compression drivers on a “SABS2” horn.
An internal crossover frequency is 2 KHz 12dB/Octave.
The STK "CIRCUIT PRO"protect to the HF driver from accidental overload.
Ultra tough, the scratch proof warnex texture coated.
Impact-resistant perforated Metal grill with weather proof powder coated.
35mm pole mount receptacle on the bottom.
With or without flying hardware options for eyebolt joint.

SPECIFICATIONS

Model	SP-156AP
ENCLOSURE SPECIFICATION
System configuration	2-Way full-range
LF Components & Loading	One SK15300 15”, vented
HF Components & Loading	One 2 inch voice coil compression driver
Operating Mode	Active
Enclosure Material	Plywood with MDF
Enclosure Finish	Black Warnex texture coated
Grill	Powder coated perforated steel
Frequency Response
±3 dB	55Hz ~19kHz
-10 dB	43Hz ~ 20KHz
Recommended High-pass Frequency	50Hz
Axial Sensitivity(dB SPL, 1 watt @ 1m)	101
Nominal Input Impedance(ohms)	4-8
Power Handling(Watts, Continuius)	Full range 300 (Internal)
Power Handling(Watts, Peak)	Full range 1200 (Internal)
Calculated SPL Limit (Referenced to 1 m)
Peak	131.8dB
Long Term	125.8dB
Normal Dispersion( degrees@-6dB )	Horizontal 85 ° Vertical 85 °
Optional Accessries	STK Eye Bolt "seb08" STK Stand "ST6180"
Demensions ( ±0.13 inch / ±3 mm)	Height 704 Front width 480 Rear width 350 Depth 480
Shipping/CBM	0.258
Net weight	36.08kg
Shipping weight	40.56 kg
AMPLIFIER SPECIFICATION
Output Power	INT	EXT
4 ohm	300W	300W
8 ohm	200W	200W
Power Bandwidth (Ref.1kHz, THD+N=0.1%, +0/-1dB)	20Hz ~ 20kHz
Frequency Response (Ref.1kHz 1 watt output, +1/-1.5dB)	20Hz ~ 30kHz
THD+N (Ref.1kHz, f=20Hz~20kHz)	0.05%
Hum & Noise	≥70 dB
Input Sensitivity	+ 4 dBu
Damping Factor	≥300
Input impedance	10k ohm
Mode select	ST/Parallel
Connectors Input	2 XLR
Connector output	1 Neutrick Type Speakon.
Cooling	Variable speed Fan
Power Requirements	980 Watts
Special Features	1. sig LED, Cilp LED, PRT LED 2. Lowest in-rush trodial X-Former 3. STK 7 Way Full Circuit Protection

*Specifications subject to change without notice.